Winkelmandje tonen (0 Artikel) Uw accountVerlanglijstje tonenNaar de kassa

AquaCon®

AquaCon® is a water based concrete release agent that aids in releasing concrete castings from Smooth-On rubber molds and other surfaces such as melamine, metal and non-porous (sealed) wood. It provides a clean, positive release, does not interfere with color or surface detail and helps minimize bug holes and air bubbles in finished castings. Coverage – Applied in a thin film (.0005 in / .013 mm), 1 gallon (undiluted) covers 3,200 square feet / 297 square meters.

AquaCon

Features
Low Cost – Use straight or dilute with water (up to 8 parts with water. See dilution recommendation below).
Water Based, Eco-Friendly – Contains no VOC’s, carcinogens or oils harmful to the environment.
Does Not Stain Concrete, affect color surface detail or finishing.
Minimizes “Bug Holes” and air bubbles.
Contains No Oils that will cause rubber molds to soften, shrink or swell.
Keeps Molds Clean - Does not build up.
Extends Mold Life
Instructions
PREPARATION... Safety - Wear safety glasses to minimize contamination risk. Store and use at room temperature (73°F/23°C). Do not use below 45°F/8°C.

Pre-Mixing - Before dispensing, shake container or stir thoroughly with a paddle or drill mixer set on a slow speed to a uniform consistency.

Diluting AquaCon® - AquaCon® can be used straight or diluted with up to 8 parts water. The dilution ratio depends on your concrete mix design. Finding the right balance between AquaCon® and water can affect bug holes. If using on a new rubber mold, it is recommended that AquaCon® be used straight (undiluted) for each casting for the first 10 castings. 1 – 10 castings, use undiluted. After 10 castings, dilute 1 part AquaCon® : 4 Parts Water After 20 castings, dilute 1 part AquaCon® : 8 Parts Water Mix only amount needed for one day. Mixture may separate in the container after a few hours. Before dispensing, pre-mix before to a uniform consistency.

Applying - Coat mold surface with a very thin film (.0005 in / .013 mm). Apply with a brush, roller, HVLP gun or Kwikee® Sprayer. Do not allow release agent to pool in the mold. Wipe over mold surface using a clean, soft cloth.

Caution: Do Not Over Apply. Applying too much release agent will cause air bubbles “wormtracks”, “bugholes” or pitting on surfaces. After applying AquaCon to mold surface, you can mix and cast concrete immediately.

Mix only amount needed for one day. Mixture may separate after 24 hours. Re-mix to a uniform consistency and apply. Because no two applications are quite the same, a small test application to determine suitability for your project is recommended if performance of this material is in question.

GUIDE

Let us help you find your way.

The list below may help you find what you are looking for via an alternative path.

  • Afvormen

    fllexibele materialen voor mallen: siliconen, pu-rubbers, alginaat etc.

  • Special Properties

  • Gietmaterialen

    Materialen voor het gieten van harde of flexibele objecten.

  • Schuimen

    Liquid Flexible Foam, Liquid Rigid Foam, Rigid Foam Blocks

  • Composieten

    Harsen, polyester, epoxy, acrylhars, glasvezels enz.

  • Cold Casting

    Metaalpoeders en plastics voor het "koud" gieten van IJzer, Brons, Messing of Tin.

  • Restauratie

    Voor het vervaardigen en herstellen van architectuur en ornamentiek.

  • Prototyping

    Materialen die worden gebruikt voor rapid prototyping

  • Textiel

  • Cosplay

    Producten om je eigen cosplay kostuums en rekwisieten te maken

FormX Newsletter Nieuwsbrief Over ons Contact Verkoopvoorwaarden Verzending we have vacancies FormX Academy Merken Toepassingen Is dit de baan voor jou?

Wij gebruiken cookies om onze website te optimaliseren en u de best mogelijke online ervaring te bieden. Door op "alles accepteren" te klikken gaat u hiermee akkoord. Geavanceerde instellingen