Winkelmandje tonen (0 Artikel) Uw accountVerlanglijstje tonenNaar de kassa

Pigments Ignite

Pigments fluorescents Ignite

The Ignite® line of liquid fluorescent colorants is compatible with Smooth-On urethane rubbers, urethane plastics, urethane foams (rigid and flexible) and silicones. The fluorescent or "glow" effect is maximized under ultra-violet light or "black light." The most dramatic color effect is realized when an Ignite colorant is used with a clear or translucent urethane rubber (such as Clear Flex 50) or plastic (such as Smooth-Cast 325).

The NEW Ignite® 9 pack gives you the opportunity to experience each color without spending a lot of money.

What Makes Castings Made With Ignite® Pigments Appear To Glow? When you add Ignite fluorescent color to a urethane material, more ultraviolet light from the cured material is visible to your eye vs. castings made with SO Strong® colorants. The casting appears brighter in ambient light and appears to glow under ultraviolet light.

Technical bulletin Ignite Fluorescent colors

Ignite Pigmenten

  • Ignite Fluor Color, Green /120ml

    Ignite Fluor Color, Green, 4 oz

    22,50 EUR (Prijs exclusief 21% BTW)

  • Ignite Fluor, Magenta /120ml

    Ignite Fluor, Magenta, 4 oz

    22,50 EUR (Prijs exclusief 21% BTW)

  • Ignite Fluor, Orange /120ml

    Ignite Fluor, Orange, 4 oz

    22,50 EUR (Prijs exclusief 21% BTW)

  • Ignite Fluor, Pink /120ml

    Ignite Fluor, Pink, 4 oz

    22,50 EUR (Prijs exclusief 21% BTW)

  • Ignite Fluor Yellow /120ml

    Ignite Fluor, Yellow, 4 oz

    22,50 EUR (Prijs exclusief 21% BTW)

  • Ignite fluorescent Color Blue /120ml

    Ignite fluorescent Color for PU and silicones, Blue, 120ml

    22,50 EUR (Prijs exclusief 21% BTW)

  • Ignite fluorescent Color Red /120ml

    Ignite fluorescent Color for PU and silicones, Red, 120ml

    22,50 EUR (Prijs exclusief 21% BTW)

  • Ignite Fluor white /120ml

    Ignite fluor Kleurstof voor PU en silicones, Wit, 120ml

    18,30 EUR (Prijs exclusief 21% BTW)

  • Ignite Fluor Purple /120ml

    Ignite fluor Kleurstof voor PU en silicones, Paars, 120ml

    18,30 EUR (Prijs exclusief 21% BTW)

  • Ignite 9 color Sampler

    Ignite 9 color Sampler

    39,25 EUR (Prijs exclusief 21% BTW)

Instructions
To get you started, we offer the following colorant loading levels. Results may vary.

By Weight Using A Gram Scale: Add Ignite™ colorant at a ratio of between 0.5% - 1.5% of the total weight (Parts A + B mixed) of the material being cast. 1% pigment yields the best results. Adding more than 1.5% by weight offers no benefit and is a waste of the colorant. Too much colorant may cause cure inhibition.

By Volume Measured In Drops: Add 30 drops of Ignite™ per 3 oz (88 ml) of mixed urethane material. If using a translucent material (like Smooth-Cast 325) you can use 15 drops to maintain translucency of the material.

Pre-Mix Before Using: Ignite™ colorants are pigment dispersions and may separate over time. They must be thoroughly pre-mixed in the container before using with a liquid urethane product.

Directions For Use: After dispensing the required amount of urethane material Parts A and B into measuring containers, add colorant to Part B and mix thoroughly. Combine Parts A and B into a mixing container and mix as directed by the urethane product technical bulletin. Blending Colors - You can combine different colors on a pallete to create a custom color before adding to liquid urethane product as directed above. Recommended loading maximum is 1% Ignite pigment by weight.

Smooth-On offers this color guide as a general reference only and assumes no responsibility for color accuracy or matching. Results will vary from one material to another. The end user is solely responsible for determining color suitability and accuracy. Small scale testing is recommended. User determines amount to add; If this is your first time adding color tint or pigment to a urethane, epoxy or silicone system, you may want to test the color effect by adding a few drops to a small amount of urethane material and observe the outcome. It may take a few test castings to attain the desired color outcome.

Looking for a clear fluorescent additive? Cryptolyte™ is a clear additive that can be added to urethane or silicone materials that will cause cured material to glow a bright blue when exposed to UV light (black light).

For fluorescent color effects in platinum silicone rubbers, use Silc-Pig™ ELECTRIC silicone pigments

Kieswijzer

Hier vindt u onze produkten gerangschikt naar diverse toepassingsmogelijkheden, zoals: Lifecasting, boetseren, afvormen, gieten, make-up, stuntwerk, dentaalwerk en studie.

Over ons Contact Costumer Projects Verzending Merken Branches Jesmonite Workshop