Winkelmandje tonen (0 Artikel) Uw accountVerlanglijstje tonenNaar de kassa

Ignite

De Ignite ® lijn van vloeibare fluorescerende kleurstoffen is compatibel met Smooth-On urethaanrubbers, urethaan plastic, urethaanschuimen (hard en flexibele) en siliconen. Het fluorescerende of "glow" effect wordt gemaximaliseerd onder ultraviolet licht of "black light." Het meest dramatische kleureffect wordt gerealiseerd wanneer een Ignite kleurstof wordt gebruikt met een helder of doorschijnend urethaan rubber (zoals Clear Flex 50) en plastic (zoals Smooth-Cast 325).

De NIEUWE Ignite ® 9 pack geeft u de mogelijkheid om elke kleur te ervaren zonder veel geld uit te geven.

Wat maakt het dat gietsels die gemaakt zijn met Ignite ® pigmenten lijken Gloeien? Wanneer u Ignite fluorescerende kleur toevoegt aan een urethaan materiaal, wordt er meer ultraviolet licht van het uitgeharde materiaal zichtbaar voor uw oog tegenover gietstukken met SO Strong ® kleurstoffen. Het gietsel lijkt helderder in omgevingslicht en lijkt te gloeien onder ultraviolet licht.

Technical bulletin Ignite Fluorescent colors

Ignite™ Pigmenten

Ignite™ Pigmenten

  • Ignite Fluor Green /120ml

    Ignite Fluor Green /4oz

    34,78 EUR

  • Ignite Fluor Magenta /120ml

    Ignite Fluor Magenta /4oz

    31,02 EUR

  • Ignite Fluor Orange /120ml

    Ignite Fluor, Orange /4oz

    31,02 EUR

  • Ignite Fluor, Pink /120ml

    Ignite Fluor Pink /4oz

    34,78 EUR

  • Ignite Fluor Yellow /120ml

    Ignite Fluor Yellow /4oz

    31,02 EUR

  • Ignite fluor Blue /120ml

    Ignite fluor /4oz

    34,78 EUR

  • Ignite fluor Red /120ml

    Ignite fluor Red /4oz

    34,78 EUR

  • Ignite Fluor white /120ml

    Ignite fluor /4oz

    31,02 EUR

  • Ignite Fluor Purple /120ml

    Ignite fluor Purple /4oz

    31,02 EUR

Instructions
To get you started, we offer the following colorant loading levels. Results may vary.

By Weight Using A Gram Scale: Add Ignite® colorant at a ratio of between 0.5% - 1.5% of the total weight (Parts A + B mixed) of the material being cast. 1% pigment yields the best results. Adding more than 1.5% by weight offers no benefit and is a waste of the colorant. Too much colorant may cause cure inhibition.

By Volume Measured In Drops: Add 30 drops of Ignite™ per 3 oz (88 ml) of mixed urethane material. If using a translucent material (like Smooth-Cast 325) you can use 15 drops to maintain translucency of the material.

Pre-Mix Before Using: Ignite® colorants are pigment dispersions and may separate over time. They must be thoroughly pre-mixed in the container before using with a liquid urethane product.

Directions For Use: After dispensing the required amount of urethane material Parts A and B into measuring containers, add colorant to Part B and mix thoroughly. Combine Parts A and B into a mixing container and mix as directed by the urethane product technical bulletin. Blending Colors - You can combine different colors on a pallete to create a custom color before adding to liquid urethane product as directed above.

There are no issues when using this product with urethane rubbers, plastics and foams or tin-catalyzed silicones. However…Ignite® pigments will drastically thicken platinum silicone rubber. Adding Ignite® colorants to a Smooth-On platinum cure silicone such as Dragon Skin® will make the silicone notably thicker, thereby affecting its ability to be vacuum degassed. Recommended loading maximum is 1% Ignite pigment by weight. An option for using Ignite® colorants with a platinum silicone may be to use pigmented material as paint for brushing on to an existing platinum silicone casting or appliance. You can use Ignite® colorants with our Psycho Paint® system.

Smooth-On offers this color guide as a general reference only and assumes no responsibility for color accuracy or matching. Results will vary from one material to another. The end user is solely responsible for determining color suitability and accuracy. Small scale testing is recommended. User determines amount to add; If this is your first time adding color tint or pigment to a urethane, epoxy or silicone system, you may want to test the color effect by adding a few drops to a small amount of urethane material and observe the outcome. It may take a few test castings to attain the desired color outcome.

Looking for a clear fluorescent additive? Cryptolyte® is a clear additive that can be added to urethane or silicone materials that will cause cured material to glow a bright blue when exposed to UV light (black light).

kieswijzer

Hier vindt u onze produkten gerangschikt naar diverse toepassingsmogelijkheden, zoals: Lifecasting, boetseren, afvormen, gieten, make-up, stuntwerk, dentaalwerk en studie.

FormX Newsletter Nieuwsbrief Over ons Contact Verkoopvoorwaarden Verzending we have vacancies FormX Academy Merken Toepassingen Is dit de baan voor jou?

Wij gebruiken cookies om onze website te optimaliseren en u de best mogelijke online ervaring te bieden. Door op "alles accepteren" te klikken gaat u hiermee akkoord. Geavanceerde instellingen